HT
Heramb Trifaley AMPP Cert #N-11954
Contact Specialist
AMPP Senior Certified Coatings Inspector | 20+ Years Certified

Heramb Trifaley
Forensic Coating Engineering

Specialized in forensic Coating Failure Analysis, comprehensive Asset Integrity Coating Surveys, and stringent QA/QC inspection under AMPP/NACE, ISO 12944, and SSPC standards.

Explore Failure Analysis Coating Survey Workflow
Certification ID
Cert No. N-11954
AMPP CIP Senior Certified
Industry Tenure
20 Years Certified
AMPP Recognition Badge
Specialization
Forensic Analysis
Coating Failures & Corrosion
Asset Integrity
Coating Surveys
ISO 4628 / ASTM D610
Heramb Trifaley - LinkedIn Profile Photo

Heramb Trifaley

AMPP Senior Certified Coatings Inspector

AMPP 20 Years Certified Badge Holder

AMPP SENIOR CERTIFIED INSPECTOR N-11954
AMPP Senior Inspector No. N-11954
AMPP 20 YEARS CERTIFIED
20 Years Certified AMPP Recognition
Senior Certified Specialist

20+ Years of Authority in Protective Coatings & Asset Integrity

As an AMPP Senior Certified Coatings Inspector (Cert No. N-11954) with over three decades of recognized field experience, I deliver specialized technical leadership in asset preservation, coating failure forensics, and third-party QA/QC compliance.

My practice focuses heavily on high-stakes industrial infrastructure—including offshore platforms, marine assets, refinery storage tanks, pipelines, and structural steelworks. I specialize in identifying non-obvious failure modes, root cause mechanics, and executing risk-based coating surveys that safeguard critical assets against aggressive corrosion environments.

ISO 12944 System Specification
SSPC-PA2 DFT Verification
NACE SP0188 Holiday Testing
Offshore & Marine Oil & Gas Infrastructure Failure Diagnostics Condition Surveys

Technical Focus Areas

Core Expertise & Engineering Services

Forensic Investigation

Coating Failure Analysis

When protective coatings break down prematurely, assets are exposed to rapid environmental attack. Root cause investigations combine thermodynamic evaluation, micro-analysis, cross-sectional microscopy, and chemical characterization to deliver definitive forensic results.

Blistering & Ageing Coating Lifespan Assessment
Delamination Intercoat contamination
Cathodic Disbondment CP over-polarization
Launch Interactive Failure Matrix
Asset Integrity

Coating Surveys & Integrity

Comprehensive visual and non-destructive coating degradation profiling (ISO 4628 / ASTM) to calculate remaining service life, optimize maintenance budgets, and prevent structural failures.

  • Dry Film Thickness (DFT) mapping & statistical profiling
  • Rust Grade Classification (ISO 4628-3 / ASTM D610)
  • Risk-Based Maintenance & Capex Planning
Try Condition Evaluator Tool
Third-Party QA/QC AMPP CIP Senior Certified Inspector Oversight

Coating Inspection & Quality Control

Ensuring strict compliance during surface preparation (SSPC-SP10/NACE 2 Near-White Blast, ISO 8501-1) and application parameters including dew point monitoring, soluble salt testing (Bresle method), dry film thickness compliance (SSPC-PA2), and high/low voltage holiday testing (NACE SP0188).

Environmental RH, Dew Pt, Surface Temp
Surface Profile Anchor Profile / Bresle
DFT Verification SSPC-PA2 Gaging
Pinhole / Holiday NACE SP0188 Spark
Interactive Diagnostic Engine

Coating Failure Analysis Simulator

Select a failure mechanism below to inspect root causes, laboratory diagnostic protocols, and preventive coating engineering solutions.

Asset Condition Profiling

Coating Degradation Evaluator (ISO 4628 / ASTM D610)

Simulate a field survey condition assessment based on visible rust breakdown area percentage and adhesion retention.

Corroded / Rusted Area (%) 1.0%
Adhesion Retention (ASTM D4541 Pull-Off) 8.5 MPa
Calculated Integrity Status
GOOD CONDITION (Ri 2)
Routine Monitoring

Coating integrity is acceptable with minimal spot breakdown. Continue scheduled maintenance cycles.

Reference Standards

Technical Knowledge Base

Strict adherence to internationally recognized standards ensures technical repeatability, asset safety, and industrial longevity.

ISO 12944 Standard

Corrosion protection of steel structures by protective paint systems.

C1 to C5 Category Atmospheric Corrosivity
CX Category Extreme Offshore Marine
Durability Target Very High (>25 Years)

AMPP / SSPC Standards

Surface preparation, dry film thickness testing, and discontinuity inspection.

SSPC-SP10 / NACE 2 Near-White Blast
SSPC-PA2 DFT Measurement Rules
NACE SP0188 High Voltage Spark Testing

Analytical Laboratory Protocols

Microscopic and spectroscopic characterization of failed coating films.

FTIR Spectroscopy Resin Identification
SEM-EDS Testing Elemental & Salt Analysis
ASTM D4541 Pull-off Adhesion Strength

Initiate Technical Consultation

Need urgent coating failure forensic investigation, asset condition surveys, or expert QA/QC representation?